Impact of COVID-19 on gender gap in dental publications: a retrospective cohort with three Brazilian journals.

This was a retrospective cohort study to investigate the impact of COVID-19 pandemic on the gender gap in articles submitted to three international dental journals based in Brazil. All submissions performed to Brazilian Dental Journal, Brazilian Oral Research, and Journal of Applied Oral Science before (2019) and during the pandemic (2020) were assessed. Gender of the first, last, and corresponding authors were collected. Other variables collected were journal, continent studied by authors and stage of their careers (classified according to authors' highest degree), and final decision reached in the article. Absolute and relative frequencies with 95% confidence intervals, Pearson's Chi-square tests, and Fisher's Exact test were used (α = 0.05). In total, 4,726 unique submissions were analyzed. A higher proportion of early-career authors was observed during the pandemic (44.8% to 49.3%, p = 0.021). Most articles were rejected but without association with gender. Increased proportion of male first authors from before to during the pandemic was observed (39% to 42.1%, p = 0.034). Drop in the proportion of articles with women as first authors was observed for researchers in their early- (65.9% to 58.8%, p = 0.02) and mid-career stages (63% to 55.8%, p = 0.014). Reduction in women as first authors was observed during the pandemic in South and Central Americas (66.7% to 61.5%, p = 0.010), and when the last author was a female, or the corresponding author was a male. In conclusion, a disproportionate impact on female dental researchers in submitting articles in the period from before to during the pandemic was observed when considering first authorship, suggesting that the COVID-19 may have increased the gender inequality in dental science.

Impact of COVID-19 on gender gap in dental publications: a retrospective cohort with three Brazilian journals

Abstract This was a retrospective cohort study to investigate the impact of COVID-19 pandemic on the gender gap in articles submitted to three international dental journals based in Brazil. All submissions performed to Brazilian Dental Journal, Brazilian Oral Research, and Journal of Applied Oral Science before (2019) and during the pandemic (2020) were assessed. Gender of the first, last, and corresponding authors were collected. Other variables collected were journal, continent studied by authors and stage of their careers (classified according to authors' highest degree), and final decision reached in the article. Absolute and relative frequencies with 95% confidence intervals, Pearson's Chi-square tests, and Fisher's Exact test were used (α = 0.05). In total, 4,726 unique submissions were analyzed. A higher proportion of early-career authors was observed during the pandemic (44.8% to 49.3%, p = 0.021). Most articles were rejected but without association with gender. Increased proportion of male first authors from before to during the pandemic was observed (39% to 42.1%, p = 0.034). Drop in the proportion of articles with women as first authors was observed for researchers in their early- (65.9% to 58.8%, p = 0.02) and mid-career stages (63% to 55.8%, p = 0.014). Reduction in women as first authors was observed during the pandemic in South and Central Americas (66.7% to 61.5%, p = 0.010), and when the last author was a female, or the corresponding author was a male. In conclusion, a disproportionate impact on female dental researchers in submitting articles in the period from before to during the pandemic was observed when considering first authorship, suggesting that the COVID-19 may have increased the gender inequality in dental science.

Intraradicular Dentin Biomodification with Natural Agents for Bonding Glass-fiber Posts.

PURPOSE: To evaluate the effects of pretreatment with different crosslinking agents on glass-fiber-post adhesive luting. MATERIALS AND METHODS: Single-rooted human teeth (n = 20) were randomly assigned to four groups: proanthocyanidins (PA) from grape-seed extract, cardol and cardanol (separated from cashew nut-shell liquid) and negative control (hydroethanolic solution). The solutions were applied on 37% phosphoric acid-etched dentin for 60 s. Glass-fiber posts were cemented using a three-step etch-and-rinse adhesive (Scotchbond Multi-Purpose, 3M Oral Care) and composite cement (RelyX ARC, 3M Oral Care). Slices for the push-out bond strength test were cut and tested after 24-h or 6-month storage in distilled water. The dentin underlying the adhesive layer was analyzed by micro-Raman spectroscopy to evaluate vibrational formation of collagen crosslinks. Three additional slices per group were also made and the adhesive in-situ degree of conversion (DC) was analyzed by micro-Raman spectroscopy. The results were analyzed using two-way ANOVA and Tukey's test (p < 0.05). RESULTS: No statistically significant changes in bond strength were found over time for any of the groups, except with cardol, which increased bond strength (8.4 ± 3.9 MPa at 24 h to 15.0 ± 2.9 MPa after 6 months, p < 0.001) after aging. The formation of peaks at 1117 cm-1 and 1235 cm-1 showed the presence of collagen crosslinks for all three biomodification agents. The DC outcomes showed no statistically significant differences between groups (p = 0.514). CONCLUSION: Biomodification agents did not impair adhesive polymerization. Cardol demonstrated a positive influence on intraradicular dentin bonding for glass-fiber post luting.

Polywave And Monowave Light-Curing Units Effects On Polymerization Efficiency Of Different Photoinitiators / Efeito Da Unidade De Cura Por Luz Polywave E Monowave Na Eficiência De Polimerização De Diferentes Fotoiniciadores

Objective: The objective of this study was to characterize and correlate the absorption spectra of three photoinitiators [camphorquinone (CQ), diphenyl(2,4,6-trimethylbenzoyl) phosphine oxide (TPO) and phenylbis (2,4,6-trimethylbenzoyl)-phosphine oxide (BAPO)], using second or third-generation light curing units (LCU), and to evaluate the degree of conversion and the physical properties of an experimental resin adhesive. Material and methods: Second-generation (Radii-cal® and Emitter D®) and third-generation (Valo® Cordless and Bluephase N®) LCU were assessed regarding spectrum and irradiance rate of emitted light. Also, the photoinitiators (CQ, TPO and BAPO) were characterized by a light absorption spectrum assessed by UV-Vis spectroscopy, degree of conversion and yellowing effect. Statistical analyzes considered two-way ANOVA and post-hoc Tukey test. Results: BAPO presented higher reactivity compared to TPO. Regarding degree of conversion of the photoinitiators activated by different light-curing units, the Emitter D® device promoted a high degree of conversion. BAPO presented the highest yellowing effect values. Conclusions: The emission and absorption characteristics of the photoinitiators were different. The polymerization reaction activated by the second-generation light-curing unit was reduced when using an experimental resin with photoinitiator TPO, and the third-generation light-curing unit showed a higher polymerization potential regardless of the photoinitiator. (AU)

Objetivo: Caracterizar e correlacionar os espectros de absorção de três fotoiniciadores [canforoquinona (CQ), difenil 2,4,6-trimetilbenzil óxido de fosfina (TPO) e óxido de di (2,4,6-trimetilbenzil) difenil fosfina (BAPO)], com unidades de fotoativação (LCU) de segunda ou terceira geração, e avaliar o grau de conversão e as propriedades físicas de um adesivo experimental. Material e métodos: LCU de segunda geração (Radii-cal® e Emitter D®) e terceira geração (Valo® Cordless e Bluephase N®) foram avaliadas quanto ao espectro e taxa de irradiância da luz emitida. Além disso, os fotoiniciadores (CQ, TPO e BAPO) foram caracterizados por um espectro de absorção de luz avaliado por espectroscopia UV-Vis, avaliado o grau de conversão dos adesivos e efeito de amarelamento. A análise estatística empregada foi ANOVA duas vias e teste post-hoc de Tukey. Resultados: BAPO apresentou maior reatividade comparado ao TPO. Em relação ao grau de conversão dos fotoiniciadores ativados por diferentes aparelhos fotopolimerizadores, o dispositivo Emitter D® promoveu um alto grau de conversão. BAPO apresentou os maiores valores de efeito de amarelamento. Conclusões: As características de emissão e absorção dos fotoiniciadores foram diferentes. A reação de polimerização ativada pelas unidades de fotopolimerização de segunda geração foi reduzida com o uso de uma resina experimental com fotoiniciador TPO. As unidades de fotopolimerização de terceira geração apresentaram maior potencial de polimerização independentemente do fotoiniciador. (AU)

A Bibliometric Analysis of Articles Published in Brazilian Dental Journal over 30 years.

This study assessed bibliometric characteristics of all articles published in Brazilian Dental Journal (BDJ) in its 30 years of existence (1990-2019) and factors associated with citation rates. A document search was carried out in Scopus in December, 2019 and information about the articles were exported, including citations. Type of study and main subject in each article were categorized. Number of citations was categorized in tertiles. Logistic regression models were used to assess the association between variables related to articles' characteristics and number of citations. In 30 years, 1705 articles were published and 18507 citations received, with average 57 articles and 334 pages published yearly and 10.9 cites/doc. The most frequent types of study were laboratorial (63%), clinical (18.5%), and case reports (11%); the main subjects were dental materials (21.6%), endodontics (19.3%), and oral pathology/stomatology (13.1%). Most articles had origin in Brazil (90%), followed by USA (4.6%) and UK (1.5%). Aside from BDJ, Journal of Endodontics (3.5%) and International Endodontic Journal (2.2%) were journals that most often cited BDJ. Main origins of citations were Brazil (36.7%), USA (10.6%), and India (9%). Older articles had higher odds to be highly cited (12% increase/year), longer articles had lower odds (9% decrease/page). Narrative reviews and epidemiological studies were associated with more citations and systematic reviews with less citations. In conclusion, BDJ covered many subjects and study types in 30 years, showing increased growth in international audience. The journal may be regarded as one of the leading Brazilian journals in dentistry published in English.

A Bibliometric analysis of articles published in Brazilian Dental Journal over 30 years

Abstract This study assessed bibliometric characteristics of all articles published in Brazilian Dental Journal (BDJ) in its 30 years of existence (1990-2019) and factors associated with citation rates. A document search was carried out in Scopus in December, 2019 and information about the articles were exported, including citations. Type of study and main subject in each article were categorized. Number of citations was categorized in tertiles. Logistic regression models were used to assess the association between variables related to articles' characteristics and number of citations. In 30 years, 1705 articles were published and 18507 citations received, with average 57 articles and 334 pages published yearly and 10.9 cites/doc. The most frequent types of study were laboratorial (63%), clinical (18.5%), and case reports (11%); the main subjects were dental materials (21.6%), endodontics (19.3%), and oral pathology/stomatology (13.1%). Most articles had origin in Brazil (90%), followed by USA (4.6%) and UK (1.5%). Aside from BDJ, Journal of Endodontics (3.5%) and International Endodontic Journal (2.2%) were journals that most often cited BDJ. Main origins of citations were Brazil (36.7%), USA (10.6%), and India (9%). Older articles had higher odds to be highly cited (12% increase/year), longer articles had lower odds (9% decrease/page). Narrative reviews and epidemiological studies were associated with more citations and systematic reviews with less citations. In conclusion, BDJ covered many subjects and study types in 30 years, showing increased growth in international audience. The journal may be regarded as one of the leading Brazilian journals in dentistry published in English.

Resumo Este estudo avaliou as características bibliométricas de todos os artigos publicados no Brazilian Dental Journal (BDJ) em seus 30 anos de existência (1990-2019) e fatores associados com taxas de citação. Uma busca pelos documentos foi realizada no Scopus em Dezembro de 2019 e informações acerca dos artigos foram exportadas, incluindo citações. Tipo de estudo e principal assunto em cada artigo foram categorizados. Número de citações foi categorizado em tercis. Modelos de regressão logística foram usados para avaliar a associação entre as variáveis relacionadas às características dos artigos e o número de citações. Em 30 anos, 1705 artigos foram publicados e 18507 citações recebidas, com média de 57 artigos e 334 páginas publicadas ao ano e 10,9 citações/documento. Os tipos de estudo mais frequentes foram laboratorial (63%), clínico (18,5%) e relato de caso (11%); os principais assuntos foram materiais dentários (21,6%), endodontia (19,3%) e patologia oral/estomatologia (13,1%). A maioria doas artigos teve origem do Brasil (90%), seguido dos EUA (4,6%) e Reino Unido (1,5%). Além do BDJ, Journal of Endodontics (3,5%) e International Endodontic Journal (2,2%) foram os periódicos que mais citaram o BDJ. As principais origem das citações foram Brasil (36,7%), EUA (10,6%) e Índia (9%). Artigos mais antigos tiveram maiores chances de serem altamente citados (aumento de 12% ao ano), artigos mais longos tiveram menores chances (redução de 9% por página). Revisões narrativas e estudos epidemiológicos foram associados com mais citações e revisões sistemáticas com menos citações. Em conclusão, o BDJ cobriu diversos assuntos e tipos de estudo em 30 anos, mostrando contínuo crescimento na audiência internacional. O periódico pode ser considerado um dos líderes entre as revistas brasileiras de odontologia publicadas em inglês.

Bond Stability of Universal Adhesives Applied To Dentin Using Etch-And-Rinse or Self-Etch Strategies.

This study evaluated the immediate and 6-month dentin bond strength of universal adhesives used in etch-and-rinse or self-etch bonding strategies. The adhesives tested were Ambar Universal, G-Bond, Single Bond Universal, Tetric N-Bond Universal, and Ybond Universal. Gold standard adhesives (Scotchbond Multipurpose Plus and Clearfil SE Bond) were controls. Microtensile dentin bond strength (n=5 teeth), pH, and C=C conversion (n=3) were evaluated. Data were analyzed at α=0.05. All adhesives showed differences in pH. Ybond had intermediately strong aggressiveness, whereas the others were ultra-mild. The C=C conversion was different in most adhesives. In the etch-and-rinse strategy, all adhesives showed similar results generally except for G-Bond, which had lower bond strength than most adhesives. G-Bond and Tetric-N-Bond showed lower bond strengths after 6 months compared with 24 h, whereas the other adhesives had stable dentin bonds. In the self-etch strategy, G-Bond had lower bond strength than most adhesives. After 6 months, Ambar was the only adhesive showing lower dentin bond strength compared with 24 h. Most adhesives had discreet drops in bond strength during aging when used in the self-etch strategy. The failure modes were also material dependent, with a general pattern of increased adhesive and/or pre-testing failures after storage. In conclusion, the bonding performance of universal adhesives to dentin is material dependent. Most adhesives had stable dentin bonds with results comparable to the gold standard materials, particularly when applied in the self-etch mode. In general, it seems the use of universal adhesives in dentin should not be preceded by phosphoric acid etching.

Modificação e avaliação de gel de ácido fosfórico 35% com agente aromatizante / Modification and evaluation of 35% phosphoric acid gel with flavoring agent

Objetivos: O condicionamento da superfície dos tecidos dentários duros com ácido fosfórico 35% é normalmente utilizado para fornecer retenção micromecânica para adesivos odontológicos. Quando lavado da superfície, o ácido pode gerar gosto amargo e desagradável ao paladar do paciente. O objetivo deste estudo foi analisar o efeito da adição de um agente aromatizante à composição do gel de ácido fosfórico 35% e investigar se existe alteração de características fundamentais deste material, como sua capacidade de desmineralizar a superfície dentária. Métodos: Além de um grupo controle (sem flavorizante), foram testados grupos de ácido fosfórico 35% com a adição de 0,5% ou 3% do aromatizante (Aroma Abacaxi Pó; Bio Green Ingredients). Foram realizadas análises de viscosidade, estabilidade do pH e de desmineralização da superfície de esmalte condicionada por microscopia eletrônica de varredura, além de teste de resistência de união ao esmalte por microcisalhamento. Resultados: Apesar dos grupos apresentarem pequenas diferenças entre si, nenhuma das alterações se mostrou significativa, exceto o aumento da viscosidade do gel contendo 3% do aromatizante. Conclusões: A adição de agente aromatizante ao gel condicionador de ácido fosfórico 35% parece ser alternativa viável para reduzir os problemas relacionados ao contato com o sabor desagradável do material, uma vez que não promoveu alteração negativa significativa nas características e comportamento do ácido(AU)

Objectives: Etching of dental hard tissues surfaces with 35% phosphoric acid is usually used to provide micromechanical interlocking with dental adhesives. When washed from the surface, the acid can cause a bitter taste unpleasant to the patient. The aim of this study was to analyze the effect of the addition of a flavoring agent to 35% phosphoric acid gel and investigate whether there is change in the fundamental characteristics of this material, including its ability to demineralize dental surfaces. Methods: In addition to a control group (without flavoring agent), groups were tested with the addition of 0.5% or 3% of the flavoring compound (pineapple flavor powder, Bio Green Ingredients) to 35% phosphoric acid. Analyses of viscosity, pH stability and demineralization of enamel surfaces by scanning electron microscopy were carried out, as well microshear bond strength to enamel. Results: Although the groups had minor differences among themselves, none of the changes were significant, except the increased viscosity of the gel containing 3% of the flavoring agent. Conclusions: The addition of flavoring agent to 35% phosphoric acid gel conditioner seems to be a viable alternative to reduce the problems related to contact with the unpleasant taste of the material, since it promoted no negative changes in the characteristics and behavior of the acid(AU)

Simple and Low-Cost Thermal Treatments on Direct Resin Composites for Indirect Use.

The aim of this study was to evaluate the influence of three low-cost additional thermal treatments, available in the dental office, on the mechanical, chemical and optical properties of a light-cured resin composite indicated for direct restorations but used as indirect restorative. The direct resin composite TPH3 (Dentsply) was light-polymerized using a light-emitting diode curing unit and submitted to three experimental additional thermal treatments: dry heat at 170 °C for 5 min, autoclave at 121 °C for 6 min, or microwave oven at 450 W for 3 min. The resin composite without any thermal treatment was used as negative control group. An indirect resin composite (Vita CM LC, Vita Zahnfabrik) was tested as a reference. Flexural strength, elastic modulus, microhardness, degree of C=C conversion, roughness before and after simulated toothbrush abrasion, translucency parameter and color difference (ΔE00) were evaluated. Data were analyzed at α=0.05. The indirect resin composite presented lower C=C conversion and mechanical performance. The flexural strength was significantly higher in the dry oven group compared with the control. The roughness was not different among groups before or after brushing, but the thermal treatments caused an increase in C=C conversion, microhardness, and elastic modulus without affecting the translucency parameter or showing visible color alteration (ΔE00<1.8). These results suggest that the use of additional thermal methods of polymerization represents an economical and simple alternative to enhance the mechanical and chemical properties of direct resin composites when used as indirect restoratives.

Simple and low-cost thermal treatments on direct resin composites for indirect use

Abstract The aim of this study was to evaluate the influence of three low-cost additional thermal treatments, available in the dental office, on the mechanical, chemical and optical properties of a light-cured resin composite indicated for direct restorations but used as indirect restorative. The direct resin composite TPH3 (Dentsply) was light-polymerized using a light-emitting diode curing unit and submitted to three experimental additional thermal treatments: dry heat at 170 °C for 5 min, autoclave at 121 °C for 6 min, or microwave oven at 450 W for 3 min. The resin composite without any thermal treatment was used as negative control group. An indirect resin composite (Vita CM LC, Vita Zahnfabrik) was tested as a reference. Flexural strength, elastic modulus, microhardness, degree of C=C conversion, roughness before and after simulated toothbrush abrasion, translucency parameter and color difference (ΔE00) were evaluated. Data were analyzed at α=0.05. The indirect resin composite presented lower C=C conversion and mechanical performance. The flexural strength was significantly higher in the dry oven group compared with the control. The roughness was not different among groups before or after brushing, but the thermal treatments caused an increase in C=C conversion, microhardness, and elastic modulus without affecting the translucency parameter or showing visible color alteration (ΔE00<1.8). These results suggest that the use of additional thermal methods of polymerization represents an economical and simple alternative to enhance the mechanical and chemical properties of direct resin composites when used as indirect restoratives.

Resumo O objetivo deste estudo foi avaliar a influência de três tratamentos térmicos adicionais de baixo custo, disponíveis no consultório dentário, nas propriedades mecânicas, químicas e ópticas de uma resina composta fotoativada indicada para restaurações diretas porém usada como restaurador indireto. A resina composta direta TPH3 (Dentsply) foi fotoativada usando um diodo emissor de luz e submetida a três tratamentos térmicos adicionais experimentais: forno seco a 170 °C por 5 min, autoclave a 121 °C por 6 min ou forno de micro-ondas a 450 W por 3 min. A resina composta sem qualquer tratamento térmico adicional foi usada como grupo controle negativo. Uma resina composta indireta (Vita CM LC, Vita Zahnfabrik) foi testada como referência comercial. Resistência à flexão, módulo de elasticidade, microdureza, grau de conversão de C=C, rugosidade antes e após abrasão por escovação simulada, parâmetro de translucidez e diferença de cor (ΔE00) foram avaliados. Os dados foram analisados considerando α=0.05. A resina composta indireta apresentou menor conversão de C=C e desempenho mecânico. A resistência à flexão foi significativamente mais alta no grupo forno seco comparado ao controle. A rugosidade não foi diferente entre os grupos antes ou após a escovação, porém os tratamentos térmicos adicionais causaram aumento na conversão de C=C, microdureza e módulo de elasticidade, sem afetar o parâmetro de translucidez ou mostrar alteração de cor visível (ΔE00<1,8). Estes resultados sugerem que o uso de métodos térmicos adicionais de polimerização representam alternativa econômica e simples para aprimorar as propriedades mecânicas e químicas de resinas compostas diretas quando utilizadas como restauradores indiretos.

Top-100 Most Cited Dental Articles with Authors from Brazil.

This study analyzes the characteristics of the top-100 most cited articles published in international dental journals with at least one coauthor affiliated to Brazil. A search in Scopus database for articles published between 1996 and 2017 was carried out in the 178 journals belonging to the category "Dentistry" identified in SCImago Journals & Country Rank. From the top-100 most cited articles, variables related to the journal, article, and authors were collected. Annual citation averages (ACA) and relative citation ratios (RCR) were calculated. Data were analyzed descriptively. There were 75 original reports and 25 reviews in the sample. The number of citations ranged between 124 and 657 (mean=202, median=168). The papers were published in 31 different journals (46% in only four journals), none based in Brazil. The most frequent subjects (61%) were Dental Materials, Endodontics, and Periodontology, which accounted for 63.6% of the total citations. The subject with the highest ACA was Oral and Maxillofacial Surgery and the subject with the highest RCR was Oral Radiology. Only 12 articles were cited more than 300 times. International collaboration was present in 61 articles and funding was reported in 49 articles. The first author was from Brazil in 70% and corresponding author in 55% of the papers. Southeast (83%) and South (20%) were the regions of Brazil with most presence of coauthors. This top-100 list is presented to provide an overview of the most cited articles and aid in supporting further analyses regarding publication and citation behaviors of Brazilian dentistry.

Top-100 most cited dental articles with authors from Brazil

Abstract This study analyzes the characteristics of the top-100 most cited articles published in international dental journals with at least one coauthor affiliated to Brazil. A search in Scopus database for articles published between 1996 and 2017 was carried out in the 178 journals belonging to the category "Dentistry" identified in SCImago Journals & Country Rank. From the top-100 most cited articles, variables related to the journal, article, and authors were collected. Annual citation averages (ACA) and relative citation ratios (RCR) were calculated. Data were analyzed descriptively. There were 75 original reports and 25 reviews in the sample. The number of citations ranged between 124 and 657 (mean=202, median=168). The papers were published in 31 different journals (46% in only four journals), none based in Brazil. The most frequent subjects (61%) were Dental Materials, Endodontics, and Periodontology, which accounted for 63.6% of the total citations. The subject with the highest ACA was Oral and Maxillofacial Surgery and the subject with the highest RCR was Oral Radiology. Only 12 articles were cited more than 300 times. International collaboration was present in 61 articles and funding was reported in 49 articles. The first author was from Brazil in 70% and corresponding author in 55% of the papers. Southeast (83%) and South (20%) were the regions of Brazil with most presence of coauthors. This top-100 list is presented to provide an overview of the most cited articles and aid in supporting further analyses regarding publication and citation behaviors of Brazilian dentistry.

Resumo Este artigo analisa as características dos 100 artigos mais citados publicados em periódicos internacionais de odontologia com ao menos um co-autor afiliado ao Brasil. Uma busca na base de dados Scopus por artigos publicados entre 1996 e 2017 foi realizada nos 178 periódicos pertencentes à categoria "Dentistry" identificados no SCImago Journals & Country Rank. Dos 100 artigos mais citados, variáveis relacionadas ao periódico, artigo e autores foram coletadas. Médias anuais de citação (MAA) e razões de citação relativa (RCR) foram calculadas. Os dados foram analisados descritivamente. A amostra foi composta por 75 artigos originais e 25 revisões. O número de citações variou entre 124 e 657 (média=202, mediana=168). Os artigos foram publicados em 31 periódicos diferentes (46% em apenas quatro periódicos), nenhum do Brasil. Os temas mais frequentes (61%) foram Materiais Dentários, Endodontia e Periodontia, somando 63,6% do total de citações. O tema com maior MAA foi Cirurgia Oral e Maxilofacial e o tema com maior RCR foi Radiologia Oral. Apenas 12 artigos foram citados mais de 300 vezes. Colaboração internacional estava presente em 61 artigos e financiamento foi reportado em 49 artigos. O primeiro autor era do Brasil em 70% e o correspondente em 55% dos artigos. As regiões do Brasil com mais co-autores presentes foram Sudeste (83%) e Sul (20%). Esta lista é apresentada para prover uma fotografia dos 100 artigos mais citados e ajudar a fomentar análises posteriores em relação a comportamentos de citação e publicação da odontologia brasileira.

Long-term bonding efficacy of adhesives containing benzodioxioles as alternative co-initiators.

This study evaluated the three-year lifespan of the bond to dentin of experimental self-etch adhesives containing benzodioxole derivatives - 1,3-benzodioxole (BDO) and piperonyl alcohol (PA) - as co-initiator alternative to amines. Adhesive resins were formulated using Bis-GMA, TEGDMA, HEMA, camphorquinone and different co-initiators: BDO, PA or ethyl 4-dimethylamino benzoate (EDAB - amine). An experimental self-etch primer was used to complete the two-step, self-etch adhesive system. Clearfil SE Bond (CSE) was used as commercial reference. Bond strength to human dentin was assessed by microtensile bond strength (µTBS) test, and failure mode was classified. Morphology of the dentin bonding interface was assessed via scanning electron microscopy (SEM). Irrespective of the dental adhesives evaluated, µTBS was higher after 24 hours compared with that after 1.5 and 3 years (p ≤ 0.001). However, adhesives with BDO and PA as co-initiators showed significantly higher bond strength than the bonding resin with EDAB (p ≤ 0.002), independent of the time evaluated. The commercial adhesive CSE showed similar bond strength compared with the other groups (p ≥ 0.05). Mixed failures were mainly observed after 24 hours, while adhesive failures were more frequently observed after 1.5 and 3 years. No notable differences in homogeneity and continuity along the bonded interfaces were detected among the materials in the SEM analysis. In conclusion, benzodioxole derivatives are feasible alternative co-initiators to tertiary amine in camphorquinone-based self-etching dental adhesive formulations.

Does translucency influence cure efficiency and color stability of resin-based composites?

OBJECTIVE: To determine if material's translucency influences the cure efficiency and color stability of resin-based composites (RBCs). METHODS: Four commercially-available RBCs indicated for aesthetic restorations were selected in different translucent/opaque shades: IPS Empress Direct (IED) A3 Dentin, A3 Enamel, Trans 20, and Trans 30; Filtek Z350 XT (FZX) A3D, A3B, A3E, and CT; Estelite ∑ Quick (EQ) OA3, A3, and CE; and Opallis (OP) DA3, EA3, and T-Neutral. Color was obtained in the L'C'h' system at three distinct periods: 24h after photoactivation (baseline), after 30d of water storage (WS), and after 30d of coffee storage (CS). The translucency parameter (TP) of each RBC was calculated at baseline. The degree of CC conversion (DC) was obtained by Fourier-transform infrared spectroscopy at 0.05mm (top) and 2mm (bottom) surfaces; the cure efficiency considered the bottom/top ratio. The CIEDE2000 color difference (ΔE00) was calculated considering the WS-baseline and CS-baseline values. Data were submitted to two-way ANOVA and Tukey's post-hoc test (α=0.05). Pearson's tests were used to analyze the correlations between TP and DC, and between TP and ΔE00. RESULTS: For all RBCs, cure efficiency was not affected by materials' translucency. A positive, significant correlation was observed between TP and DC at the bottom surface for FZX only. For all RBCs, the higher the TP, the higher the ΔE00. The ΔE00 was higher after CS than after WS, except for EQ A3. Positive correlation between TP and ΔE00 were observed for all materials. CONCLUSION: The translucency did not influence the cure efficiency but affected the color stability for all RBCs. CLINICAL SIGNIFICANCE: High-translucent RBCs presented lower color stability and should be used carefully.

Long-term bonding efficacy of adhesives containing benzodioxioles as alternative co-initiators

Abstract This study evaluated the three-year lifespan of the bond to dentin of experimental self-etch adhesives containing benzodioxole derivatives - 1,3-benzodioxole (BDO) and piperonyl alcohol (PA) - as co-initiator alternative to amines. Adhesive resins were formulated using Bis-GMA, TEGDMA, HEMA, camphorquinone and different co-initiators: BDO, PA or ethyl 4-dimethylamino benzoate (EDAB - amine). An experimental self-etch primer was used to complete the two-step, self-etch adhesive system. Clearfil SE Bond (CSE) was used as commercial reference. Bond strength to human dentin was assessed by microtensile bond strength (µTBS) test, and failure mode was classified. Morphology of the dentin bonding interface was assessed via scanning electron microscopy (SEM). Irrespective of the dental adhesives evaluated, µTBS was higher after 24 hours compared with that after 1.5 and 3 years (p ≤ 0.001). However, adhesives with BDO and PA as co-initiators showed significantly higher bond strength than the bonding resin with EDAB (p ≤ 0.002), independent of the time evaluated. The commercial adhesive CSE showed similar bond strength compared with the other groups (p ≥ 0.05). Mixed failures were mainly observed after 24 hours, while adhesive failures were more frequently observed after 1.5 and 3 years. No notable differences in homogeneity and continuity along the bonded interfaces were detected among the materials in the SEM analysis. In conclusion, benzodioxole derivatives are feasible alternative co-initiators to tertiary amine in camphorquinone-based self-etching dental adhesive formulations.

Rubbing time and bonding performance of one-step adhesives to primary enamel and dentin.

OBJECTIVES: This study investigated whether increasing the concentration of acidic monomers in one-step adhesives would allow reducing their application time without interfering with the bonding ability to primary enamel and dentin. MATERIAL AND METHODS: Experimental one-step self-etch adhesives were formulated with 5 wt% (AD5), 20 wt% (AD20), or 35 wt% (AD35) acidic monomer. The adhesives were applied using rubbing motion for 5, 10, or 20 s. Bond strengths to primary enamel and dentin were tested under shear stress. A commercial etch-and-rinse adhesive (Single Bond 2; 3M ESPE) served as reference. Scanning electron microscopy was used to observe the morphology of bonded interfaces. Data were analysed at p<0.05. RESULTS: In enamel, AD35 had higher bond strength when rubbed for at least 10 s, while application for 5 s generated lower bond strength. In dentin, increased acidic monomer improved bonding only for 20 s rubbing time. The etch-and-rinse adhesive yielded higher bond strength to enamel and similar bonding to dentin as compared with the self-etch adhesives. The adhesive layer was thicker and more irregular for the etch-and-rinse material, with no appreciable differences among the self-etch systems. CONCLUSION: Overall, increasing the acidic monomer concentration only led to an increase in bond strength to enamel when the rubbing time was at least 10 s. In dentin, despite the increase in bond strength with longer rubbing times, the results favoured the experimental adhesives compared to the conventional adhesive. Reduced rubbing time of self-etch adhesives should be avoided in the clinical setup.

Rubbing time and bonding performance of one-step adhesives to primary enamel and dentin

Abstract Objectives: This study investigated whether increasing the concentration of acidic monomers in one-step adhesives would allow reducing their application time without interfering with the bonding ability to primary enamel and dentin. Material and methods: Experimental one-step self-etch adhesives were formulated with 5 wt% (AD5), 20 wt% (AD20), or 35 wt% (AD35) acidic monomer. The adhesives were applied using rubbing motion for 5, 10, or 20 s. Bond strengths to primary enamel and dentin were tested under shear stress. A commercial etch-and-rinse adhesive (Single Bond 2; 3M ESPE) served as reference. Scanning electron microscopy was used to observe the morphology of bonded interfaces. Data were analysed at p<0.05. Results: In enamel, AD35 had higher bond strength when rubbed for at least 10 s, while application for 5 s generated lower bond strength. In dentin, increased acidic monomer improved bonding only for 20 s rubbing time. The etch-and-rinse adhesive yielded higher bond strength to enamel and similar bonding to dentin as compared with the self-etch adhesives. The adhesive layer was thicker and more irregular for the etch-and-rinse material, with no appreciable differences among the self-etch systems. Conclusion: Overall, increasing the acidic monomer concentration only led to an increase in bond strength to enamel when the rubbing time was at least 10 s. In dentin, despite the increase in bond strength with longer rubbing times, the results favoured the experimental adhesives compared to the conventional adhesive. Reduced rubbing time of self-etch adhesives should be avoided in the clinical setup.

Should my composite restorations last forever? Why are they failing?

Composites resins have become the first choice for direct anterior and posterior restorations. The great popularity is related to their esthetic appearance and reduced need of sound tissue removal as compared with former treatments. Several studies have demonstrated that composite restorations may last long in clinical service. In this review we discuss the factors playing a role on the long-term longevity. Composite restorations have demonstrated a good clinical performance with annual failure rates varying from 1% to 3% in posterior teeth and 1% to 5% in anterior teeth. Factors related to the patients such as caries risk and occlusal stress risk, in addition to socioeconomic factors, may affect the survival significantly. Characteristics of the clinical operators, particularly their decision making when it comes to observing or approaching an existing restoration, are decisive for longevity. Cavity features such as the number of restored walls, composite volume, and presence of endodontic treatment are of major importance and may dictate the service time of the restorative approach. The choice of restorative composite seems to have a minor effect on longevity provided that appropriate technical procedures are used. The main reasons for failure in posterior teeth are secondary caries and fracture (restoration or tooth/restoration), while in anterior teeth esthetic concerns are the main reasons leading to restoration failures. Composite resin restorations can be considered a reliable treatment as long as both the professional and the patient are aware of the factors involved in restoration failures.

Should my composite restorations last forever? Why are they failing?

Abstract Composites resins have become the first choice for direct anterior and posterior restorations. The great popularity is related to their esthetic appearance and reduced need of sound tissue removal as compared with former treatments. Several studies have demonstrated that composite restorations may last long in clinical service. In this review we discuss the factors playing a role on the long-term longevity. Composite restorations have demonstrated a good clinical performance with annual failure rates varying from 1% to 3% in posterior teeth and 1% to 5% in anterior teeth. Factors related to the patients such as caries risk and occlusal stress risk, in addition to socioeconomic factors, may affect the survival significantly. Characteristics of the clinical operators, particularly their decision making when it comes to observing or approaching an existing restoration, are decisive for longevity. Cavity features such as the number of restored walls, composite volume, and presence of endodontic treatment are of major importance and may dictate the service time of the restorative approach. The choice of restorative composite seems to have a minor effect on longevity provided that appropriate technical procedures are used. The main reasons for failure in posterior teeth are secondary caries and fracture (restoration or tooth/restoration), while in anterior teeth esthetic concerns are the main reasons leading to restoration failures. Composite resin restorations can be considered a reliable treatment as long as both the professional and the patient are aware of the factors involved in restoration failures.

Restabelecimento funcional e estético com coroas e facetas laminadas / Functional and aesthetic reestablishment with full crowns and laminate veneers ­ a case report

A adequada estética do sorriso é cada vez mais almejada pelo paciente e pelo profissional. Dentes escurecidos e com lesões de abfração, causadas por excessiva carga oclusal, desfavorecem o agradável aspecto dos dentes e a estética facial como um todo. Este caso clínico relatou o procedimento restaurador de dentes anteriores superiores que apresentavam cor e forma inadequadas. Foram confeccionadas facetas e coroas com cerâmica termoprensada reforçada por dissilicato de lítio (IPS e.max Press, Ivoclar), que tem sido frequentemente utilizada na confecção de restaurações em dentes anteriores e posteriores por apresentar propriedades estéticas e mecânicas satisfatórias. Após a reabilitação, pôde-se perceber que o detalhado planejamento do tratamento e a correta escolha do material restaurador resultaram no restabelecimento funcional e estético. Foi possível concluir que restaurações obtidas a partir da cerâmica de dissilicato de lítio mostraram ser uma ótima alternativa para a confecção de facetas e coroas, considerando que houve perfeita concordância de cor entre ambas as restaurações, resultando no sucesso do tratamento e satisfação do paciente.

Adequate aesthetic appearance of the smile is increasingly desired by patient and professional. Darkened teeth and abfraction injuries caused by excessive occlusal load jeopardizes the appearance of the teeth, and the facial aesthetics as a whole. This case describes the restorative treatment of upper anterior teeth that presented inadequate color and form. Crowns and laminate veneers were made with lithium disilicate ceramic, which has often been used in the fabrication of anterior tooth restorations because it presents satisfactory aesthetic and mechanical properties. After the restorative process, it can be concluded that the detailed treatment planning and the correct choice of restorative material result in the reestablishment of function and aesthetics. It was concluded that the lithium disilicate ceramic showed to be an excellent alternative for making laminate veneers and adjacent crowns, considering that there was perfect color matching between both restorations, resulting in the success of treatment and patient satisfaction.